Role: {{ value }} Which best describes your role?

Your response helps us make our online experience better to provide content that is specific to your role.

Thank you. Your response helps us make our online experience better to provide content that is specific to your role.

From adhesives to sealants: we offer you a complete range of accessories to achieve the perfect EPDM roofing installation. That way you can enjoy the convenience of having all components for a total EPDM roofing system from a single source, another guarantee for the highest quality.

Discover our range of accessories:

QuickSeam Products

Discover our range of EPDM field-seaming products. They are easy to use and deliver long-term performance.

QuickPrime Plus

Designed to clean and prepare the RubberGard EPDM membrane and/or substrates that are to receive a QuickSeam product, Pourable Sealer and/or Lap Sealant.

QuickSeam Splice Tape

Designed for field splicing RubberGard EPDM membrane panels.

QuickSeam Reinforced Perimeter Fastening Strip (RPFS)

Strip of RubberGard MAX Reinforced EPDM membrane with QuickSeam tape factory-laminated to it along one edge. It is used for non-penetrating base tie-ins, as described in the Elevate guidelines.

QuickSeam R.M.A. Strip

Strip of Elevate RubberGard EPDM MAX reinforced membrane with two QuickSeam tape strips factory-laminated to it along its length. It is used for non-penetrating RubberGard EPDM membrane attachment, as specified in the Elevate guidelines.

QuickSeam Batten Cover Strip

Semi-cured EPDM strip laminated to QuickSeam tape. It is used to cover and seal batten strips which are installed over the membrane, as specified in the Elevate guidelines.

QuickSeam FormFlash

Uncured EPDM strip factory‐laminated to QuickSeam tape. It is designed to flash inside and outside corners, pipes, penetrations and other applications as specified in the Elevate guidelines.

QuickSeam SA Flashing

Non-reinforced 1.5 mm thick RubberGard EPDM membrane, fully laminated to QuickSeam tape. It has a polyester release liner for easy removal and excellent weather resistance. It can be used to easily flash details where cured EPDM is required or preferred: curbs, parapets, gutters, general roof repairs, drain and pipe flanges.

QuickSeam Flashing

Semi-cured EPDM strip laminated to QuickSeam tape. It is designed to flash metal roof edging profiles and other details, as specified in the Elevate guidelines.

QuickSeam Pipe Flashing

Pre-fabricated pipe boot with a QuickSeam tape laminated to the bottom of its flange. Specifically designed for flashing rigid round penetrations of 25 mm to 152 mm.

QuickSeam Conduit Flashing

Pre-fabricated pipe boot with a QuickSeam tape laminated to the bottom of its flange. Specifically designed for flashing rigid round penetrations and conduits of 13 mm to 64 mm.

Penetration Pocket Kit

Specifically designed to be used around small pipe penetrations, clusters of pipes, l-beams, etc.

QuickSeam Walkway Pad

High-quality rubber pads with QuickSeam tape factory-laminated to the bottom. They are used for protection of the RubberGard EPDM membrane in areas of regular roof traffic.

Adhesives

Discover our high-performance bonding adhesives designed for adhering the RubberGard EPDM roofing membrane to different substrates.

Bonding Adhesive BA-2012

Solvent-based contact adhesive specifically designed for bonding RubberGard EPDM membranes to approved insulations, in addition to wood, metal, masonry and other acceptable substrates.

Bonding Adhesive BA-2012 S/TF

Sprayable solvent-based contact adhesive specifically designed for bonding RubberGard EPDM membranes to approved insulations, in addition to wood, metal, masonry and other acceptable substrates.

Bonding Adhesive BA-2004 (T)

Solvent-based contact adhesive specifically designed for bonding RubberGard EPDM membranes to wood, metal, masonry, PIR insulation boards, Elevate ISOGARD™ HD cover boards and other acceptable substrates.

Modular Water-Based Bonding Adhesive E

Specifically designed for wet-mating RubberGard EPDM membranes onto acceptable wooden substrates in an indoor environment. It can also be used as a contact adhesive onto approved insulations and other acceptable substrates, in addition to wood.

Sealants

Designed to ensure that all RubberGard EPDM installation details are completely watertight.

Lap Sealant HS

Designed to seal and mechanically protect the exposed edges of QuickSeam products where required, as per Elevate guidelines. It can also be used as a general-purpose sealant in other applications, as specified in the Elevate guidelines.

Water-Block Seal (S-20)

Designed to provide a watertight seal when used in compression at drain and scupper details, wall terminations, and other details, as specified in the Elevate guidelines.

Pourable Sealer S-10

Two-component sealer designed to create a watertight seal around small pipe penetrations, clusters of pipes, I-beams etc. in a penetration pocket detail or in other applications, as specified in the Elevate guidelines.

Cleaning agents & coatings

The RubberGard EPDM membrane can be cleaned and coated using Elevate’s bespoke products.

Splice Wash (SW-100)

Designed to clean and prepare contaminated RubberGard EPDM membranes in areas to receive adhesives where required by Elevate specifications and details.

Cleaner C-20

Alcohol-based degreaser with extremely fast evaporation properties, designed for efficiently removing all types of Elevate adhesives, sealants and other types of contamination from EPDM membranes, metal and many other solvent-resistant surfaces.

AcryliTop PC‐100

Aesthetic coating that can be applied over all RubberGard EPDM membranes, whether new or existing.

Plates, fasteners & tools

All-Purpose and Heavy Duty Fasteners are specifically designed screws for mechanical attachment of the RubberGard EPDM membrane, roofing insulation or accessories such as batten bars, termination bars, etc. to steel, wood and concrete decks.

A quality RubberGard EPDM installation only requires a few simple but effective tools.

Insulation Fastening Plates

Specifically designed to be used in combination with Elevate’s All‐Purpose and Heavy‐Duty fasteners in roofing applications for attaching Elevate PIR insulation boards, Elevate ISOGARD HD cover boards or other approved insulation/cover boards.

V-Plates

Specifically designed to be used in combination with Elevate’s All‐Purpose and Heavy‐Duty fasteners to attach (reinforced) RubberGard EPDM membranes and QuickSeam RPF strip.

Metal and Coiled Metal Batten Strips

Pre-punched galvanized steel strips for anchoring EPDM membrane sheets.

Termination Bar

Aluminium profile in C shape that is designed for attachment and termination of the RubberGard EPDM membrane against upstands with a smooth and even finishing surface such as concrete, steel, etc.

Spray Gun and hose

Professional spray gun with extension to be used in combination with the 4.0 m rubber hose. They are specifically designed to spray Elevate sprayable bonding adhesives

QuickScrubber pad and handle

Used for the application of the QuickPrime Plus primer.

QuickScrubber Plus stand-up tool

Used for the application of the QuickPrime Plus primer on upstands.

Silicone rubber roller

Used for rolling QuickSeam accessories.